Beginner's Plumbing: What You Need for Bathtub Installation
Beginner's Plumbing: What You Need for Bathtub Installation
Blog Article
They are making several good annotation on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in the article followed below.
Setting up a bathtub isn't specifically rocket science, yet it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately difficult project. If the old tub is easily easily accessible, the task can relocate speedily; if you need to open up a wall to remove the old tub and also position the brand-new tub, the job is much harder. In either case, the task is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and also embeded in the new one. See to it you have actually certified yourself for the job and also are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed task, it is far better to consider utilizing one prior to you begin. Opportunities are you may need a specialist plumber to make tube connections.
This article will certainly assist you set up a new bathtub in your shower room if you have currently acquired a new bathtub and also don't require to transform the arrangement of your previous supply of water pipes.
Your devices and also material checklist ought to consist of the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water. After doing so, turn on the taps to drain any type of water remaining in the system. The process of eliminating the existing taps can be rather troublesome because of the limited access that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old sealing substance.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin making sure that the washing machines are in location in between the tap as well as the sink. Secure the faucet in position with the producer given backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be attached to the tap finishes initially, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the bathtub in the required position. The wood boards are practical in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The next objective is to make certain that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the tub till the level checks out level.
To install taps, fit all-time low of the outermost versatile tap port to the ideal supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the water system as well as inspect all joints and also brand-new pipework for leakages as well as tighten them if required. Fill up the tub and likewise check the overflow outlet and also the regular outlet for leakages.
Lastly, fix the bath paneling as explained in the producer's user's manual. Tiling and sealing around the bathtub must wait until the tub has actually been made use of a minimum of when as this will certainly resolve it right into its final position.
Planning for the Setup
Firstly, the supporting structure provided with the bath needs to be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to avoid pressure on the tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last placement.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, causing the water to pass through the wall surface in between the bathroom and the tiling, resulting in problems with dampness and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes and also cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the tub is in use. The sealer can fracture rather early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly readily available on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub? Write a remark below. We will be glad to see your suggestions about this article. We are looking forward to see you back again before long. So long as you appreciated our article please don't forget to pass it around. Thank you so much for your time invested reading it.
Efficient help? Call! Report this page